10/24/19

Bats! A tutorial


Going Batty for Bats! 

So, a few years ago I was walking by a stationary store during October and saw this cool confetti in the window. Lightbulb! I had an idea.  Bat swarms!

Over the years I've made these for different games, friends and family, etc. Thought it was time to do a tutorial.  This tutorial goes over all the basics I've learned (some the hard way) and how I based this particular unit, for Kings of War.

Parts is Parts

The bat swarm is made up of three parts: bat confetti, insect mounting pins, and super glue gel.
Bats- found on Amazon, but check your local shops first

Bat Confetti:  These plastic bats are a great size for 28mm "Vampire" style bats. A bag of a bajillion of them costs from $1.99- $3.  Not only are they a good shape, the plastic bends well into animated poses.


Insect Mounting Pins

Caution- very sharp! 

Over the years I've used various methods to make "stands" for my bats, from larger straight pins to styrene rod. I think these insect pins are the best as they are the thinnest thing I could find, and are quite strong.  They come in different heights and sizes, but the size 2 pins which are 60mm tall I think do the trick.  Cost is about $7.00, but you get a 100 pins.  In my example I have about 23 bats on my base, so that's a total cost of $10.00-ish for  4-5 units worth of swarms!  Here's a link to the pins on Amazon


Super Gluin-it Right!

I'm all over the place with glues, but I've been liking the Gorilla Glues lately.  I do reccomend gel glues over regular so that the bats "stick" better.  Also I'm showing the pin vise I use to drill holes into the base.


Assembly 

This part is both easy and tricky.  Your first thought, as was mine, was dip the tip of the pin in glue, stick it to a bat, and done!  The trick here is the glue takes a bit of time to set, and the bats slide off and glue themselved to your table or fingers or pants (yeah, I found one) instead. Here's the trick I learned.

I use postit notes to put the glue on. Then roll the pin head to get a good "gob" of glue.


After putting glue onto the pin, stick the pin in something. I had a cardboard box close by, so used it.
Then, take a bat and balance it on the pin and let the glue do it's work.  Make sure to space them far enough apart as you are doing this so that you don't bump the other bats.  Let them dry for a good hour before mounting- which gives us time to do the base.

Bats on a stick!


All your Base!

 I'm basing this unit for Kings of War. In the forces of the Abyss army list you can have flying imps, so these could be statted like that. Honestly these could be considered fast cave of any type- it's really up to you! Back to basing. I started with one of my "troop" size Kings of War bases that I make, and trim the sides down with a box cutter blade, creating a bevel, which helps blend it into the terrain.
MDF KoW base

Always cut away from you!!!


I want some height variation to help the bat swarm look, swarmy... so added some cork to the base. they I spread glue on and added flocking sand. It was a hot day, so I put it outside for about 15 minutes and it was all dry.
Cork is cool stuff! (and easy to mount pins in) 

base covered in sand. I need to get more!
After it was dry, I gave it a base coat of Vallejo flat earth, and some dark grey(Foundry Stoneb 57b) on the cork to make them into rocks, and drybrushed with light earth and a bit of P3 menoth white base and grey  to lighten everything up a bit and grab details. Use whatever colors best work for you.


Add water to the mix. you have a lot to cover! 

Good enoufh as this will be flocked as well.

Once the paint was dry, I glued some flocking and some bushed on (but forgot to take a picture of that). I did this before mounting the bats so I would not get glue and grass accidently on the pins.

Pinning and mounting 

To make a good swarm, you will want to vary the heights of the bats. To do that you will need wire cutters to clip the pins. CAUTION  this is an important thing I've learned in doing this. Those tiny needle sharp off cuts will go flying and you will find them the hard way sometime later. I got one stuck really deeply in my foot. Here's the trick Tape! Befor cutting, place the pin on the sticky side of a piece of masking tape. When you clip it, the off cut stays on the tape.  I cut about half my bats pins, some really low, some mid ish. Play around and do what feels good.
Sticky side up! 

One piece of tape goes far- and is easily disposed of. 
Once cut, I started from the center of my base and worked my way out. drilling small holes and gluing the bats in. Before gluing, I bent the wings by gently pinching them with my fingers. Note that some of the bats, if not well glued, will pop off. I Made extras just in case, and re-glued the others on for future basing.  The cork works out great to give extra height to the overall look, and is easy to stick pins in.
nearly finished! 

Don't be afraid to play around- add more bats, bend wings, angle pins for movement
Top down. Note no bat goes past the base edge. 

Side view- this shows how I was trying to get them to swoop down.


Touching up! 

Once all together I play around with some of the wings, and see if I need to add more or less bats to create a flow. The plastic bats are very shiny plastic, but dull down perfectly once you seal the whole thing with a matte spray.  One thing I did do before I sealed the bats, was to go in with some dark brown and "gesture" the bodies, heads and wing frames. Nothing fancy and very "loose" painting, just enough to break up the shapes a bit. When I varnished the unit, the brown kinda got lost, so I'm going to go back and hit it again I think. I may also try a bit of grey.

Done! 

This entire project took about 2 hours, including waiting for paint to dry.  I'll be making more swarms, and using a few bats to dress up bases for my Triumph of Death undead.  I hope this was helpful, and I look forward to seeing your bat swarms.  Here's more pictures next to miniatures for scale.

Cheers!
Ths



9 comments:

  1. That is very inventive, and really captures a Hammer Horror vibe.

    ReplyDelete
  2. Great effect! Thanks for sharing such a detailed tutorial as well. I particularly appreciate the tape and needle point tip as that sounds as though it was hard won knowledge.

    ReplyDelete
  3. Creative and wonderful work, very atmospheric!

    ReplyDelete
  4. Hi Thomas. I'm getting reminders about returning my Kickstarter requests. Could you kindly check your emails as I have s query. Many thanks Mike

    ReplyDelete
  5. Great idea.
    I put a link to your page on my next blog's edition.

    Cheers
    Eric

    ReplyDelete
  6. Great idea, lovely tutorial, the tip about the masking tape is really smart!
    Best Iain

    ReplyDelete